中国建设银行网站对公业务,大连市建设学校网站,wordpress 关闭站点,wordpress怎么制作首页华为PPPOE配置实验 网络拓扑图拓扑说明电信ISP设备配置用户拨号路由器配置查看是否拨上号是否看不懂#xff1f; 看不懂就对了#xff0c;只是记录一下命令。至于所有原理#xff0c;等想写了再写 网络拓扑图 拓扑说明 用户路由器用于模拟家用拨号路由器#xff0c;该设备… 华为PPPOE配置实验 网络拓扑图拓扑说明电信ISP设备配置用户拨号路由器配置查看是否拨上号是否看不懂 看不懂就对了只是记录一下命令。至于所有原理等想写了再写 网络拓扑图 拓扑说明 用户路由器用于模拟家用拨号路由器该设备为pppoe的客户端 电信ISP设备则模拟电信的网络设备该设备为pppoe的服务端 而中间交换机则用于模拟光猫光猫为桥接模式此处不做任何配置当场傻瓜式设备使用电信ISP设备配置 Huaweisystem-view # 进入系统视图 [Huawei]sysname ISP # 配置路由器名字 [ISP]aaa [ISP-aaa]local-user huawei password cipher huawei [ISP-aaa]local-user huawei service-type ppp [ISP-aaa]quit [ISP]ip pool pppoe [ISP-ip-pool-pppoe]network 100.64.254.0 mask 24 [ISP-ip-pool-pppoe]gateway-list 100.64.254.1 [ISP-ip-pool-pppoe]dns-list 114.114.114.114 223.5.5.5 [ISP-ip-pool-pppoe]quit [ISP]interface Virtual-Template 1 [ISP-Virtual-Template1]ip address 100.64.254.1 24 [ISP-Virtual-Template1]remote address pool pppoe [ISP-Virtual-Template1]ppp authentication-mode chap [ISP]interface GigabitEthernet 0/0/0 [ISP-GigabitEthernet0/0/0]pppoe-server bind virtual-template 1用户拨号路由器配置 dialer-ruledialer-rule 1 ip permit interface Dialer1link-protocol pppppp chap user huaweippp chap password cipher %$%$guxPdzPzFWUHp:EdW,%o%$%$ppp pap local-user huawei password cipher %$%$0VL)HZ/u8~H]sNN#yiY,K\%$%$ip address ppp-negotiatedialer user HUAWEIdialer bundle 1dialer-group 1nat outbound 3000 acl number 3000 rule 100 permit ip interface GigabitEthernet0/0/0pppoe-client dial-bundle-number 1 查看是否拨上号 [jiucai]display ip interface brief Interface IP Address/Mask Physical Protocol Dialer1 100.64.254.254/32 up up(s) GigabitEthernet0/0/0 unassigned up down [jiucai]ping 100.64.254.1PING 100.64.254.1: 56 data bytes, press CTRL_C to breakReply from 100.64.254.1: bytes56 Sequence1 ttl255 time80 msReply from 100.64.254.1: bytes56 Sequence2 ttl255 time50 msReply from 100.64.254.1: bytes56 Sequence3 ttl255 time20 msReply from 100.64.254.1: bytes56 Sequence4 ttl255 time30 ms--- 100.64.254.1 ping statistics ---4 packet(s) transmitted4 packet(s) received0.00% packet lossround-trip min/avg/max 20/45/80 ms [jiucai]display dialer interface Dialer 1 Dial Interface:Dialer1Dialer Timers(Secs):Auto-dial:300 Compete:20 Enable:5Idle:120 Wait-for-Carrier:60[jiucai]display interface Dialer 1 Dialer1 current state : UP Line protocol current state : UP (spoofing) Description:HUAWEI, AR Series, Dialer1 Interface Route Port,The Maximum Transmit Unit is 1500, Hold timer is 10(sec) Internet Address is negotiated, 100.64.254.254/32 Link layer protocol is PPP LCP initial Physical is Dialer Current system time: 2023-08-18 14:48:11-08:00Last 300 seconds input rate 0 bits/sec, 0 packets/secLast 300 seconds output rate 0 bits/sec, 0 packets/secRealtime 0 seconds input rate 0 bits/sec, 0 packets/secRealtime 0 seconds output rate 0 bits/sec, 0 packets/secInput: 0 bytesOutput:0 bytesInput bandwidth utilization : 0%Output bandwidth utilization : 0% Bound to Dialer1:0: Dialer1:0 current state : UP , Line protocol current state : UPLink layer protocol is PPP LCP opened, IPCP opened Packets statistics:Input packets:0, 0 bytesOutput packets:4, 336 bytesFCS error packets:0Address error packets:0Control field control error packets:0是否看不懂 看不懂就对了只是记录一下命令。至于所有原理等想写了再写